数学建模社区-数学中国

标题: 大神帮忙看看，问题出在哪里？急 [打印本页]

作者: 数据分析师 时间: 2013-10-18 17:06
标题: 大神帮忙看看，问题出在哪里？急
本帖最后由数据分析师于 2013-10-18 17:08 编辑

MODEL:
sets:
FWPT/1..20/:a;
FSD/1..13/:b;
Distance(FWPT,FSD):c,x;
endsets
data:
a=1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1;
b=1 1 1 1 1 1 1 1 1 1 1 1 1;
c= 222.36160.2992.868192.94210.96225.02228.93190.01195.16120.8458.81 118.5 48.852204.64141.3 73.881 173.95191.98206.03211.21172.29 177.44103.1139.822 103.1 60.351183.52127.6760.256160.32178.35192.41190.09151.17156.3281.99660.93981.97943.934219.97150.0982.669182.74200.76214.82226.54162.27155.3581.03 48.61 73.959 3.5176.28129.7 62.279162.35177.5 191.55182.85113.07106.1531.82994.21124.75852.55176.59130 62.585162.65177.8 191.86183.16113.37106.46 32.13594.51725.06453.373149.15109.0141.596141.66150.36164.42155.7285.70280.1555.831 73.52712.90279.916140.9294.33926.922126.99142.14156.19147.5 102.28 104.93 30.608 58.85430.99586.773130.1182.74215.325115.39131.32145.38136.6897.757107.2434.92347.25741.99493.36775.866127.7669.56695.10877.08 91.13582.437141.95151.4379.114101.5 86.186147.6137.91483.374113.9550.72432.69646.75138.053186.33195.82123.5 145.88130.57191.99100000119.5 145.4386.85468.82664.77135.917217.81227.3 154.98177.36162.05223.4759.77159.733127.1527.0839.05545 23.854228.08237.57165.25161.21172.32213.32119.5 100000 67.41732.65 50.67864.73383.587180.5 189.17114.84101.48121.91153.59170.3 132.9865.564165.63171.51185.57176.8747.51857.00544.01597.49651.086118.1145.4367.417100000100.07118.1 132.15151 113.08121.7547.42734.05954.49886.169218.92149.0381.616181.68199.71213.77225.49186.57195.24120.9247.557127.9978.206242.47185.15117.73217.8 235.82249.88249.04210.12215.27140.9583.67 136.9967.344225.47169.62102.2 202.27220.29234.35232.04193.12198.26123.9476.393119.9950.337269.46212.13144.71244.78262.81276.87276.03230.11223.19148.87110.66141.8 64.489;
enddata
min=@sum(Distance(I,J):c*x);
@for(FWPT(I):@sum(FSD(J):x(I,J))<=b(J));
@for(FSD(J):@sum(FWPT(I):x(I,J))=a(I));
@for(Distance(I,J):@bin(x(I,J)));
END

Lingo提示错误代码为161
是说@for(FSD(J):@sum(FWPT(I):x(I,J))=a(I));这一行里面这个FSD(J)里的J在前面已经定义过了，可前面程序里没有啊，我也对照过标准程序，还是错了，请大神指点！谢谢！急用！

作者: 袁海亮 时间: 2013-10-19 01:00
楼主你好我用lingo11 运行错误提示为29 c的赋值有点乱，你整理好c 的赋值看一下

欢迎光临数学建模社区-数学中国 (http://www.madio.net/)