数学建模社区-数学中国

标题: 求救！各位高手帮忙指正下这个lingo程序！谢谢啊。 [打印本页]

作者: zongjieliang 时间: 2009-9-7 17:19
标题: 求救！各位高手帮忙指正下这个lingo程序！谢谢啊。
本帖最后由 zongjieliang 于 2009-9-7 20:55 编辑

求各位高手帮忙指正，不甚感谢！数据在附件中。
model:
sets:
collect/c1..c39/;
recycle/r1..r11/;
handle/h1..h2/;
kind/k1,k2/;
zero/0/;
rz(recycle,zero):g;
hz(handle,zero):t;
cr(collect,recycle):dist;
rh(recycle,handle):length;
crk(collect,recycle,kind):x,y;
rhk(recycle,handle,kind):z,u;
ck(collect,kind):A;
rk(recycle,kind):E;
hk(handle,kind)： Q,F;
endsets
data
dist=@file('e:\collect.txt');
length=@file('e:\collect.txt');
A=@file('e:\collect.txt');
enddata
!流量约束;
@for(ck(i,j):
  @sum(recycle(s):x(i,s,j))+@sum(recycle(s)|s#ge#2:y(i,s,j))=A(i,j));
@for(kind(j):
  @sum(collect(i):x(i,1,j))-@sum(handle(p):x(1,p,j))-@sum(handle(p)|p#ge#2:y(1,p,J))=0);
@for(rk(s,j)|s#ge#2:
  @sum(collect(I):x(I,S,J)+y(I,S,J))-@sum(handle(p):z(s,p,j))-@sum(handle(p)|p#ge#2:u(s,p,j))=0);
@for(kind(j):
  @sum(recycle(s):z(s,1,j)=Q(1,j)));
@for(hk(p,j)|p#ge#2:
  @sum(recycle(s):z(s,p,j)+u(s,p,j))=Q(p,j));
!能力约束;
@sum(ck(i,j):x(i,1,j))>=30*G(1,0);
@sum(ck(i,j):x(i,1,j))<=60*G(1,0);
@sum(rk(s,j):z(s,1,j))>=45*T(1,0);
@sum(rk(s,j):z(s,1,j))<=70*T(1,0);
@for(recycle(s)|s#ge#2:
  @sum(ck(i,j):x(i,s,j))>=30*G(s,0);
  @sum(ck(i,j):x(i,s,j))<=60*G(s,0));
@for(rk(s,j)|s#ge#2:
  @sum(collect(i):y(i,s,j))>=25*E(s,j);
  @sum(collect(i):y(i,s,j))<=50*E(s,j));
@for(handle(p)|p#ge#2:
  @sum(rk(s,j):z(s,p,j))>=45*T(p,0);
  @sum(rk(s,j):z(s,p,j))<=70*T(p,0);
@for(rh(p,j)|p#ge#2:
  @sum(handle(s):u(s,p,j))>=40*F(s,j);
  @sum(handle(s):u(s,p,j))<=80*F(s,j));
!新建工厂的数量限制;
@sum(rk(s,j)|s#ge#2:G(s,j)<=3);
@sum(hk(p,j)|p#ge#2:T(s,j)<=4);
!目标函数;
min=@sum(crk(i,s,j):0.0003*dist(i,s)*x(i,s,j))+@sum(crk(i,s,j)|s#ge#2:0.0003*dist(i,s)*y(i,s,j))
+@sum(rhk(s,p,j):0.0003*length(s,p)*z(s,p,j))+@sum(rhk(s,p,j)|p#ge#2:0.0003*length(s,p)*u(s,p,j))
+@sum(crk(i,s,j):0.4*x(i,s,j))+@sum(crk(i,s,j)|s#ge#2:0.4*y(i,s,j))
+@sum(rhk(s,p,j):0.7*z(s,p,j))+@sum(rhk(s,p,j)|p#ge#2:0.7*u(s,p,j))
+@sum(handle(s)|s#ge#2:50*E(s,1)+40*E(s,2)+60*G(s,0))
+@sum(handle(p)|p#ge#2:700*F(p,1)+600*F(p,2)+800*T(p,0));
@for(rz(s,0)： @bin(g));
@for(hz(p,0)： @bin(t));
@for(rk(s,j)|s#ge#2：  @bin(E));
@for(hk(p,j)|p#ge#2：  @bin(F));
end

collect.rar

1.03 KB, 下载次数: 1, 下载积分: 体力 -2 点

作者: wsccool 时间: 2009-9-7 19:34
太长了就容易出错``我再仔细看下

作者: zongjieliang 时间: 2009-9-7 20:56
多谢啊！你帮忙仔细看看，我就搞不清楚错在哪!谢谢！

作者: zwb1030 时间: 2009-9-8 08:30
想下下来看看
没有矩币
晕

作者: zongjieliang 时间: 2009-9-8 11:53
....不是吧，还需要矩币才能下？我晕。。。。。

欢迎光临数学建模社区-数学中国 (http://www.madio.net/)