查看: 4441|回复: 1

关于多媒体播放器VCD左右声道问题的BC代码

字体大小: 正常放大

3 主题	1 听众	29 积分

升级 25.26%

该用户从未签到

电梯直达

1^#

发表于 2004-9-30 19:11 |只看该作者 |倒序浏览

|招呼Ta 关注Ta

<

>关于多媒体播放器在CB下声道转换的原代码！（DEPHI版的网上有）
<

>TSuperPlayerform *SuperPlayerform;
typedef struct
{
DWORD dwCallback;
DWORD dwItem;
DWORD dwValue;
DWORD dwOver;
LPSTR lpstrAlgorithm;
LPSTR lpstrQuality;
} MCI_DGV_SETAUDIO_PARMS;

const MCI_SETAUDIO = 0x873;
const MCI_SETVIDEO = 0x0876;
const MCI_DGV_SETAUDIO_SOURCE_LEFT=1;
const MCI_DGV_SETAUDIO_SOURCE_STEREO=0;
const MCI_DGV_SETAUDIO_SOURCE_RIGHT=2;
const MCI_DGV_SETAUDIO_SOURCE=0x4004;
const MCI_DGV_SETAUDIO_VOLUME=0x4002;
const MAX_VOLUME=65535;
const MIN_VOLUME=0;
<

>void __fastcall TSuperPlayerform:

RC(char &S)
{
 //char str;
 MCI_DGV_SETAUDIO_PARMS s;
 int err;
 char buf[1001];
 //str=''L'';
 if (MediaPlayer1->DeviceID>0)
 {
err=mciSendCommand(MediaPlayer1->DeviceID,MCI_SETAUDIO,MCI_SET_OFF,int(&s));
if (err!=0)
 mciGetErrorString(err,buf,sizeof(buf) );
if (S=='C')
 s.dwValue=MCI_DGV_SETAUDIO_SOURCE_STEREO;
if (S=='L')
 s.dwValue=MCI_DGV_SETAUDIO_SOURCE_LEFT;
if (S=='R') s.dwValue=MCI_DGV_SETAUDIO_SOURCE_RIGHT;
 s.dwItem=MCI_DGV_SETAUDIO_SOURCE;
const MCI_DGV_SETAUDIO_VALUE=0x01000000L;
const MCI_DGV_SETAUDIO_ITEM=0x00800000L;
//(MCI_DGV_SETAUDIO_VALUE||MCI_DGV_SETAUDIO_ITEM)=0x01800000
err=mciSendCommand(MediaPlayer1->DeviceID,MCI_SETAUDIO,0x01800000,int(&s));
if (err!=0)
 mciGetErrorString(err,buf,sizeof(buf) );
err=mciSendCommand(MediaPlayer1->DeviceID,MCI_SETAUDIO, MCI_SET_ON ,int(&s));
if (err!=0)
 mciGetErrorString(err,buf,sizeof(buf) );
}
}
<

> void __fastcall TSuperPlayerform::popnosoundClick(TObject *Sender)
{
 LRC('L');
 Label3->Caption=“左声道 ";
 tempchannel='L';
}
//---------------------------------------------------------------------------
<

> void __fastcall TSuperPlayerform::popsoundClick(TObject *Sender)
{
 LRC('R');
 Label3->Caption="右声道 ";
 tempchannel='R';
}
//---------------------------------------------------------------------------
<

> void __fastcall TSuperPlayerform::steroClick(TObject *Sender)
{
 LRC('C');
 Label3->Caption="立体声 ";
 tempchannel='C';
}

zan

转播0 淘帖0 分享0 收藏0 支持0 反对0 微信

使用道具举报

ilikenba

1万主题	49 听众	2万积分

TA的每日心情

	奋斗 2024-6-23 05:14

签到天数: 1043 天

[LV.10]以坛为家III

群组: 万里江山

群组: sas讨论小组

群组: 长盛证券理财有限公司

群组: C 语言讨论组

群组: Matlab讨论组

2^#

发表于 2004-9-30 20:30 |只看该作者 |招呼Ta 关注Ta

<

>左右声道的设置代码！从网上找到的！<

>lReturn=mciSendString("set left off",sReturn,32,0)
lReturn=mciSendString("set right off",sReturn,32,0)
lReturn=mciSendString("setaudio left off",sReturn,32,0)
lReturn=mciSendString("setaudio right off",sReturn,32,0)
确切地说，以上四句关闭的并不是左右声道，而是左右音箱。由于通常的多媒体音频流多是立体声的，并不是左音箱播放的完全是左声道的音频流，其中掺入轻微的右声道声音，以达到更好的立体效果。
要想关闭左右声道可以这样：
lReturn=mciSendString("setaudio source to left",sReturn,32,0) '仅开左声道
lReturn=mciSendString("setaudio source to right",sReturn,32,0) '仅开右声道
lReturn=mciSendString("setaudio source to average",sReturn,32,0) '左右平均
lReturn=mciSendString("setaudio source to stereo",sReturn,32,0) '立体声，这是默认设置